Electrostatic AIRMIX® solution with ISOCUBE for water-based paints

This solution is a simple AIRMIX® concept using our ISOCUBE for spraying water-based paint with an additional electrostatic effect
solution isocube airmix
solution isocube airmix

Complete solution for electrostatic Airmix® applications with water-based materials

PERFORMANCE
  • Adjustment of the fan width and the electrostatic effect on the spray gun
  • High transfer efficiency thanks to the wrap around effect limiting the material losses on the booth 
PRODUCTIVITY
  • Plug & spray solution that's easy to assemble
  • Intuitive settings from the spray gun or from the controller   
SUSTAINABILITY
  • Robust construction that can be transported easily
  • Careful selection of parts in contact with the material to ensure perfect compatibility with water-based paints   

  

ISOCUBE Airmix® electrostatic water-based applications

We offer several water-based electrostatic options using either our ISOCUBE solutions

Nanogun Airmix® aircap
(1) Aircaps and Tips

The Nanogun Airmix® spraygun must be fitted with our genuine Airmix® spray tips to guarantee the best finish quality, minimum overspray, and pattern repeatability.

You must choose the right tip required for thickness and fan width pattern (for example, use 09.09 tip size to apply 90 µm in manual applications). To help you select your spray tip, please refer to the tip configurator. 

Tips and Tricks:  At the end of the day, leave the aircap and nozzle  - only those 2 parts - in the water until the next use.

 

Nanogun Airmix H2O
(2) Nanogun Airmix® electrostatic spray gun

The Nanogun Airmix® H20 version does not require ATEX compliance and can be use in job coaters activities as long as the ventilation is correctly renewed. 

Tips and Tricks: The use of our gun cover will  pertfectly protect your gun. When you flush, we recommend you place your gun on the side wall of the paint container to prevent any splashing.

We advise you to use low additional air to create a penetrating spray pattern which will perfectly reach recessed areas.For flat and wide surfaces, higher additional air will give a finer atomization and a wider spray pattern resulting in glossy finished surface.

Isocube by SAMES KREMLIN
(3) ISOCUBE AND CONTROL PANEL

Specially dedicated to the Nanogun Airmix® electrostatic spray gun : user-friendly, it yields a high voltage/current constant curve. The control panel allows to control the atomization air, the pump pressure (air for product pressure) and flow rate adjustment.

Tips and Tricks: for a safe and quick start-up, always check that the Isocube is properly grounded as the state of the art.  Then check your paint viscosity (up to 50s CA4) , then, stirr well the paint before priming. You need to start the pump smoothly to prevent air entraped in the fluid circuit.   

product Hoses
(4) Hoses

You will need to select the right length of hoses between the paint pump and the spray gun depending on your installation and your spray booth location . 

Tips and Tricks: For operator safety , only use our genuine hoses (7,5 and 15 m) and in any case and never make any hose extension.

10C18 Airmix® Paint Pump
(5) Cup lub Airmix® paint pump

This cup lub pump range represents an economical production/price ratio. Those pumps are dedicated for solvent and water-based paints.

Our SAMES KREMLIN pump range features fluid sections made of stainless steel.  This pump is not recommended for moisture-sensitive materials. In case of multiple color changes, we recommend using the smallest hydraulic section which matches your needs to save paint and solvents materials. 

Tips and Tricks: In the case of very viscous materials, this pump type can be fed under pressure.

17F60 Airmix® Flowmax Paint Pump
(5) Flowmax® Airmix® paint pump

This free lub pump range represents the most robust paint pump in the world. Our SAMES KREMLIN Flowmax® bellows pump range is dedicated for abrasive and moisture sensitive solvent or water-based materials. 

The fluid section is made of stainless steel. This pump is not recommended for multiple color changes.

Tips and Tricks:

  • In case of viscous materials, you should never exceed 0,5 bar feeding pressure.
  • Never use  a check valve integrated on the suction rod (you may damage the Flowmax® bellow) .
Filtration
(6) FILTRATION

The main filtration can be done at the paint pump using a dedicated filter mounted at the product output of the paint pump. The filter screen need to be adjusted depending on your paint to prevent tip blockage when spraying.

We supply two different types of filters:

    the inline filter which requires a very small amount of solvent for flushing sequences
    the filter accumulator which is the one which is usually mounted on our pumps.

Tips and Tricks: Place the filter with the vessel oriented on the top to be used as an accumulator 

Isocube interior details
(7) Pump feeding: suction rod

 Allows you to pump the material directly from a drum container. Different suction hose diameters are available regarding the viscosity of the paint. We supply suction rods for drums with a capacity of 60 liters and 200 liters.

Tips and Tricks: Even if the suction rod is not a wear part, we recommend you check it daily as the strainer is not plugged. Always keep a couple extra strainers in stock! 

Mixing agitator
(7) Pump feeding: agitator

An agitator will maintain all the components of the paint in constant movement preventing any deposition of pigments and will keep the best performance of the pump and the gun. It will also ensure perfect homogenous colors during the application.

Tips and Tricks: When manipulating the agitator, we highly recommend you shut down the air in the circuit , even if the ball valve is off.

Pumps selection criteria table to help you choose the right pump which will meet your needs

Kit Name

Product pressure
(bar/psi)

Fan size
(mm)

Gun Included Paint Feed Hoses Regulator Hose Sleeve

Airmix®
ISOCUBE

120/1740 upon tip size Nanogun Airmix® H20 15C25 7.5m Air - ID8mm
​7.5m Fluid - ID6.5mm
Yes Yes
Airmix®
ISOCUBE
200/2900 upon tip size Nanogun Airmix® H20 30C25 7.5m Air - ID8mm
​7.5m Fluid - ID6.5mm
Yes Yes
Airmix®
​ISOCUBE
120/1740 upon tip size Nanogun Airmix® H20 15C25 15m Air - ID8mm
​7.5m Fluid - ID6.5mm
Yes Yes
Airmix®
ISOCUBE
200/2900 upon tip size Nanogun Airmix® H20 30C25 15m Air - ID8mm
15m Fluid - ID6.5mm
Yes Yes