Silicone grease is commonly used for lubricating & preserving rubber parts, such as O-rings. Additionally silicone grease does not swell or soften the rubber, which can be a problem with hydrocarbon-based grease. It functions well as a corrosion-inhibitor & lubricant for purposes that require a thicker lubricant. Thermal grease often consists of a silicone grease base along with added thermally conductive fillers. It is used for heat transfer abilities rather than friction reduction.
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.
Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.
Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.
Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.
Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.
Silicone sealants can be used in two or three components for increasing mechanical capabilities.
Accelerator speeds up the setting process for 1K sealant to achieve rapid rain resistance & thorough setting of the accelerated foundation sealant.
Polyester Powder Coatings allows long-term exterior durability, high performance mechanical properties & over-bake resistance. Polyester powder is widely used for decorative parts where a good resistance to sunlight (ultraviolet rays) are required. Many automotive trim components & other exterior parts are coated with polyester powders.
Nylon is a thermoplastic. Meaning its chemistry does not change when it is melted to the metal part. Nylon will melt and re-melt if the metal part is heated again. Nylon coating powder is aesthetically attractive when applied properly but is never specified simply because it looks good. Costing more than 3 times the typical paint or powder finish, nylon is specified for functionality IE: slip, sound dampening, flange linings, and medical case brackets. Other types of parts we apply nylon to are: drive splines, glove box strikers, door strikers, seat springs, and various clips and clamps used in the aerospace and auto industries. Nylon powder for use in coating metal can be purchased in two chemistries: nylon 11 or nylon 12. What is the difference? The chemist may argue there are plenty of differences, however, practically speaking Nylon 12 is slightly less hygroscopic than Nylon 11 (less than 1%) Nylon 12 typically will have lower gloss, and nylon 12 may be slightly less expensive to purchase depending on the amount ordered. When buying nylon, gloss can not be specified. Generally, nylon 11 is around 70 gloss. Nylon 12 is typically 30 gloss. Gloss level will be the same batch to batch, and will only vary depending on the manufacturing process. Nylon is considered a "softer" coating, easily machinable, but can not be easily marked with a fingernail.
Polyurethane powders have excellent flow characteristics with excellent chemical and mechanical properties. Outstanding corrosion resistance and excellent external exposure properties make them suitable alternative to polyester powders. GENERAL FEATURES Polyurethane powder contains polyurethanic resins cured with curing agents. The powder forms protective and decorative film along with enhanced outdoor resistance. The protective film have good resistance to mechanical damage, detergents, fuels and oils.
Some anti-corrosion materials are available in water-based versions. These green paints have a longer dry time, but meet most environmental requirements & have excellent protective qualities.
블라스팅 된 강철에 적용되는 아연 코팅은 탁월한 방청 스프레이 코팅 부식 방지, 풍화 방지 및 해수 및 용제에 대한 우수한 내성을 제공합니다. 무기 아연 코팅은 화학 플랜트, 정유소 및 연안 또는 해양 설비에 사용될 때 탁월한 방청 부식 방지 기능을 제공합니다. 이 코팅은 탑 코트를 적용 할 때 더 나은 부식 방지 기능을 제공 할 수 있습니다. 무기 아연 코팅은 에폭시, 페놀, 아크릴, 실리콘 및 기타 여러 코팅과 호환됩니다.
무용제 에폭시 코팅은 부식, 마모 및 화학적 공격으로부터 강철 및 콘크리트 구조물을 장기간 보호하기 위해 설계되었습니다. 작동 온도 범위는 –40F ~ 1040F입니다.
금속 표면 및 광범위한 도장 시스템에서 첫 번째 층으로 사용되는 2 액형 효율적인 코팅 제품. 우수한 품질의 방식 성 폴리 우레탄 필름을 형성하여 표면과 도장 공정의 다음 층 사이의 접착을 보장합니다.
부식 방지 에폭시는 코팅 할 철 및 강철 표면의 부식 방지 및 방청을 위해 사용됩니다. 그것은 매우 단단하고 마찰에 강합니다. 특히 희석 된 산, 알칼리, 석유 제품, 일부 용제, 물, 해수 등에 내성이 있습니다.
Bitumen is an oil-based substance. It is a semi-solid hydrocarbon product produced by removing the lighter fractions (such as liquid petroleum gas, petrol & diesel) from heavy crude oil during the refining process.
Anti-fouling paint, or bottom paint, is a specialized coating applied to the hull of a ship or boat to slow the growth of sub-aquatic organisms that attach to the hull & can affect a vessel's performance & durability.
폴리 우레탄 코팅은 적용하기에 특히 경제적이기 때문에 강철의 부식 방지에 종종 사용됩니다. 빠르게 건조되므로 짧은 간격으로 오버 코팅 할 수 있습니다. 또한 날씨 조건과 독립적으로 적용될 수 있으며 충격에 강합니다.
Enamel paint air dries to a hard, typically glossy finish, and is used for coating surfaces that are outdoors or otherwise subject to hard wear or temperature changes.
폴리 우레탄 (PU 또는 PUR)은 고정 된 조성을 가진 단일 물질이 아니라 유사한 화학 물질을 공유하는 다양한 화학 물질입니다. 우레탄 또는 카바 메이트 연결로 연결된 유기 사슬 단위로 구성된 폴리머입니다. 대부분의 폴리 우레탄은 열경화성 폴리머이며, 열가소성 폴리 우레탄과 달리 가열 될 때 녹지 않습니다.
2 성분 폴리 우레탄 (2C PUR이라고도 함)은 단일 성분 폴리 우레탄 접착제의 장점을 갖지만 더 큰 간격을 통해 더 빨리 경화되며 경화를위한 수분 / 열에 의존하지 않습니다.
MS 폴리머는 차세대 실리콘 및 매 스틱입니다. 다른 제품과 달리이 제품은 특정 프라이머를 사용하지 않고도 대부분의 기질에 잘 부착됩니다. 이러한 제품을 사용하면 응용 프로그램 실수의 위험을 줄일 수 있습니다.
Water-Based Wood Stains have all the advantages of oil-based stains. They spread easily, can be repaired, blend effortlessly & have plenty of open time. The thicker formula allows for controlled penetration, which will reduce blotching on softer woods such as Aspen, Pine & Maple.
A wood stain consists of a colorant suspended or dissolved in an agent or solvent. Colored, or ''stained", finishes do not penetrate the pores of the wood to any significant degree.
Chemical Agent Resistant Coating (CARC) is available in a water-based solution for environmental protection.
Chemical Agent Resistant Coating (CARC) is a paint commonly applied to military vehicles to provide protection against chemical & biological weapons. The surface of the paint is engineered to be easily decontaminated after exposure to chemical warfare & biological warfare agents. The paint is also resistant to damage & removal by decontaminating solutions.
Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.
Catalyzed polyurethane clear coats and paints are prized for their durability and versatility around the world. They are used on everything from wood cabinetry, mill work and furniture to planes, trains, and automobiles. They are usually mixed with isocyanates in the hardener. The isocyanate component of polyurethane reacts with moisture in the air and form a hard crystalline structure.
UV-resistant epoxy systems mixed with hardener cure faster & in moist conditions.
UV coatings can be formulated up to 100% solids so that they have no volatile component that contributes to pollution.
Water-based UV coatings can be considered aesthetically equivalent to bi-component acrylic & polyurethane solvent-based coatings. The range is composed of both pigmented & transparent products.
UV curable epoxy systems do not require the addition of curing agents. They cure within minutes, or even seconds, and have unlimited working times.
The UV polyurethane multi-components are especially designed for very strong UV stability. Mixing with hardener gives very high durability & UV resistance.
The UV polyurethanes are especially designed for UV stability, The coating is long lasting, offers excellent substrate protection, provides an attractive finish & is user-friendly.
Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.
Top Coat Epoxys are used for decorative flooring applications, such as Terrazzo flooring, chip flooring & colored aggregate flooring.
Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.
Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.
멀티 컴포넌트 에폭시산 촉매(AC) 시스템은 건조/경화를 위해 경화제 또는 촉매가 필요하며, 화학 반응이 완료될 때까지 바인더의 경화 과정을 시작하고 유지함으로써 작동한다. 용제는 화학반응이 일어나기 전에 옻칠, 페인트 또는 필러로 마무리된다. 촉매는 습기에 민감하며 Flowmax® 기술 보호가 필요하다.
Multi-Component Epoxy Acid Catalyzing (AC)시스템은 건조/경화를 위해 경화제 또는 촉매가 필요하며, 화학 반응이 완료될 때까지 바인더의 경화 과정을 시작하고 유지함으로써 작동한다. 용제는 화학반응이 일어나기 전에 옻칠, 페인트 또는 필러로 마무리된다. AC 제품의 경화 시간은 열을 가하면 극적으로 빨라질 수 있다.
The newest metallic epoxy system on the market allows contractors to heighten the effects & make floors look three-dimensional.
Polyurethane water-based coatings offer a very high chemical/physical resistance & steel effect & are environmentally friendly.
A two-component 100%-solid epoxy blended with metallic pigments, Metal Fusion is self-leveling, allowing easy application & seamless floor surfaces.
Polyurethane coatings are particularly recommended for application to surfaces subject to high levels of wear & tear where excellent chemical/physical resistance is required. The metallic parts will give a steel effect.
Protection, bonding, finishing & sealing for composite & plastic parts